Search Results

Gouges and scratches to rollover protection structures are informative to the reconstruction and analysis of real-world vehicle rollover crashes. Variations in ground surface composition can be correlated with accompanying witness marks on the vehicle rollover protection structure. This paper presents the results of rollover protection structure specimen tests using a variety of test speeds and surface compositions. The test results and analyses that follow are displayed for use in comparison to similar damage on subject crash vehicles. In addition, impact of steel rollover protection structures with various opposing ground surface materials can produce visible sparks in low light conditions. Tests were performed to show the ability of these structures to produce sparks from various surface impacts.

The accuracy of collision severity data recorded by event data recorders (EDRs) has been previously measured primarily using barrier impact data from compliance tests and experimental low-speed impacts. There has been less study of the accuracy of EDR-based collision severity data in real-world, vehicle-to-vehicle collisions. Here we used 189 real-world front-into-rear collisions from the Crash Investigating Sampling System (CISS) database where the EDR from both vehicles recorded a severity to examine the accuracy of the EDR-reported speed changes. We calculated relative error between the EDR-reported speed change of each vehicle and a speed change predicted for that same vehicle using the EDR-reported speed change of the other vehicle and conservation of momentum. We also examined the effect of vehicle-type, mass ratio, and pre-impact braking on the relative error in the speed changes.

Building upon prior research, this paper compares computer simulations to a previously conducted rollover crash test of a tractor-semitrailer. The effects of torsional stiffness were elucidated during the correlation of simulations to the rollover test. A commercially available vehicle dynamics and reconstruction software was used for the simulation. Unique aspects of the rollover crash test were modeled in the simulation. A tractor-semitrailer quarter-turn rollover crash test conducted by IMMI was reconstructed using impact and vehicle dynamics models within the simulation software HVE (Human, Vehicle & Environment). The SIMON (SImulation MOdel Non-linear) module and the DyMESH (Dynamic MEchanical SHell) module within HVE were used. During the IMMI test, onboard instrumentation recorded acceleration and roll rate data in six degrees of freedom to characterize both tractor and semitrailer dynamics before and during the rollover event.

The rapid advancement of new energy vehicle technology has led to the widespread placement of battery packs at the bottom of vehicles. However, there is a lack of corresponding regulations and standards to guide aspects related to vehicle bottom safety. This lack of guidance obscures the relative importance of various parameters impacting the structural safety of battery packs under dynamic impact conditions. Consequently, research on battery pack bottom collisions holds practical significance and offers valuable reference material. This study proposed a method based on the first collision point to examine the impact of bottom collisions on the mechanical safety performance of battery pack bottoms. A finite element model of the battery pack was established to investigate the effects of different impact types.

Background: The Indian automobile industry, including the auto component industry, is a significant part of the country’s economy and has experienced growth over the years. India is now the world’s 3rd largest passenger car market and the world’s second-largest two-wheeler market. Along with the boon, the bane of road accident fatalities is also a reality that needs urgent attention, as per a study titled ‘Estimation of Socio-Economic Loss due to Road Traffic Accidents in India’, the socio-economic loss due to road accidents is estimated to be around 0.55% to 1.35% of India’s GDP [27] Ministry of road transport and highways (MoRTH) accident data shows that the total number of fatalities on the road are the highest (in number terms) in the world. Though passenger car occupant fatalities have decreased over the years, the fatalities of vulnerable road users are showing an increasing trend. India has committed to reduce road fatalities by 50% by 2030.

The Bendix Wingman Fusion – a radar and camera collision mitigation system (CMS) available on commercial vehicles – was evaluated in two separate test series to determine its performance in simulated rear collision scenarios. In the first series of tests, evaluations were conducted in daytime, nighttime, and rainy conditions between 15 to 58 miles per hour (mph) to evaluate the performance of the audible and visual forward collision warning (FCW) system in a first-generation Bendix Wingman Fusion CMS while approaching a stationary live vehicle target (SLVT) in a 2017 Kenworth T680. A second test series was conducted with a 2017 Kenworth T680 traveling at 50 mph in daytime conditions approaching a decelerating vehicle to evaluate the Bendix Wingman Fusion CMS on the truck. Both test series sought to determine the maximum distance the system would warn prior to the test driver swerving around the SLVT or moving vehicle target.

Abstract Compared to other age groups, older adults are at more significant risk of hip fracture when they fall. In addition to the higher risk of falls for the elderly, fear of falls can reduce this population’s outdoor activity. Various preventive solutions have been proposed to reduce the risk of hip fractures ranging from wearable hip protectors to indoor flooring systems. A previously developed rubberized asphalt mixture demonstrated the potential to reduce the risk of head injury. In the current study, the capability of the rubberized asphalt sample was evaluated for the risk of hip fracture for an average elderly male and an average elderly female. A previously developed human body model was positioned in a fall configuration that would give the highest impact forces toward regular asphalt.

To harmonize and define terminology associated with occupant protection for children for vehicle manufacturers and child restraint manufacturers in the United States and Canada.

This user’s manual covers the instrumented arm for the Hybrid III 5th Percentile Small Female dummy as well as the SID –IIs dummy. It is intended for technicians and engineers who have an interest in assessing arm injury from the use of frontal and side impact airbags. It covers the construction, disassembly and reassembly, available instrumentation, and segment masses.

Over the years the vehicle population has drastically grown which increases the number of road accidents. The accident severity caused fatality and disability being reduced by introducing energy absorption materials (Crash tube). Over the years, researchers have used aluminium, magnesium, and titanium crash tubes to enhance the energy absorption characteristics during different crash scenarios. However crash tube will possess sufficient rigidity to absorb the impact force during collision but it is still challenging to identify the right material. At the same time, this paper aims to examine the energy absorption characteristics of Aluminium-Magnesium hybrid material (Al-Mg 5456) crash tube designs. Three designs were considered square, cylindrical, and hexagonal designs along with different notch designs to minimize the weight percentage of tubes. The LSDYNA results the oval notches performed better in energy absorption when compared to other designs.

In day-to-day life, accidents do occur frequently all around the globe. It is difficult to prevent these accidents as they occur due to different reasons, which cannot be easily controlled. However, the fatal injuries occurring to passengers can be reduced by installing efficient safety systems in vehicles, which will help in saving the lives of mankind. Many safety systems are being installed in vehicles such as seat belt restraints, airbags, etc. Generally, three-point seat belts are installed in passenger vehicles for safety purposes. This type of seat belt doesn't arrest the entire motion of the occupant's body during vehicle crashes, which can lead to fatal injuries and sometimes even death during vehicle crashes. To buckle passengers with seats, we can use five-point seat belts which will help in mitigating the injuries as compared to three-point seat belts.

The design and analysis of the roll cage for the ATV car are the subjects of this report. The roll cage is one of the key elements of an ATV car. It is the primary component of an ATV, on which the engine, steering, and gearbox are mounted. The vehicle's sprung mass is beneath the roll cage. The initiation of cracks and the deformation of the vehicle are caused by forces acting on it from various directions. Stresses are consequently produced. FEA of the roll cage is used in this paper in an effort to identify these areas. We have performed torsional analysis as well as front, rear, side impact, and rollover crash analyses. These analyses were all completed using ANSYS Workbench 2020 R1. The design process complies with all guidelines outlined in the SAE rule book of E-Baja.

In regions with hot and humid climatic conditions, lightweight cotton textiles such as lawns, are famous for clothing and being explored for use in automobile interiors. Specifically, there’s an interest in these fabrics for car seat covers, interior roof linings, and door trims. Textiles must balance weight and durability for automotive applications to ensure passenger comfort while withstanding regular wear and tear. This study assesses cotton fabrics’ wear and mechanical performance with densities between 40 and 60 g/m2, produced using yarn counts of 70, 60, and 40 Ne. The objective was to determine the optimal fabric parameters for creating automotive spare parts that are both durable and comfortable. Two production strategies were contrasted: coarser yarn counts with fewer warp and weft threads per inch and finer yarn counts with a higher thread density.

Researchers have chosen to study natural fibers instead of synthetic fibers since low-cost and ecologically favorable materials are required. The present research concentrates on the mechanical characteristics of epoxy composites reinforced with bamboo and bagasse fibers. The hybrids were created using four different ratios of bamboo/bagasse fibers, then hand-laid up. The material characteristics of the generated composites, including tension, bending, impacts, and Shore D hardness measurements, were assessed. The scanning electron microscopy technique was used to study morphology. Three levels of bamboo and a core network of bamboo fibers in composites were assumed to generate superior qualities. The core layer of bamboo and an outer layer typically characterized by sugarcane composites have enhanced flexural strength and Shore D toughness because of the bamboo layer at the center.

• AIRBAG COMPONENT MINIMUM PERFORMANCE REQUIREMENTS • AIRBAG INSTALLATION PERFORMANCE REQUIREMENT Current revision will only contain Part 25 and lapbelt installed airbags. Future revisions will expand to include Structural airbags, 3-point restraint airbag, pre-tensioner etc.

Bamboo fibers were used as reinforcement in hardened epoxy mixes altered with ethoxylated soybean oil (ESO) to enhance the mechanical and thermal qualities. Compared to a bio-based epoxy mix, the tensile strength and modulus of the laminate with 20% bamboo fiber were higher. During thermogravity analysis (TGA) evaluation, it was discovered that the rate of deterioration peak had been moved to a warmer temperature, indicating improved thermal durability of the aggregate over the base material. The dynamic mechanical evaluation of the bio-based composite anticipated increased storage modulus and greater glass transition temperatures. High fiber–matrix adherence was visible in scanning electron morphology (SEM). Measurements of the interfacial adhesion demonstrate the hydrophilicity of the bio-based reinforced composites. The binding and effective insemination of fibers is responsible for the fiber-reinforced composite’s durability.

This SAE Information Report describes the testing and reporting procedures that may be used to evaluate and document the excursion of a worker or civilian when transported in a seated and restrained position in the patient compartment of a ground ambulance when exposed to a front, side, or rear impact. Its purpose is to provide seating and occupant restraint manufacturers, ambulance builders, and end-users with testing procedures and documentation methods needed to identify head travel paths in crash loading events. This is a component level test. The seating system is tested in free space to measure maximum head travel paths. The purpose is not to identify stay out zones. Rather, the goal is to provide ambulance manufacturers with the data needed to design safer and functionally sound workstations for Emergency Medical Service workers so that workers are better able to safely perform patient care tasks in a moving ambulance.

Heavy Commercial Road Vehicles (HCRVs) may be more susceptible to rollover incidents due to their higher centre of gravity position than passenger vehicles, and rollover is one of the significant causes of HCRV accidents. Therefore, variation in vehicle roll behaviour becomes crucial to the safety of an HCRV. Toe misalignment is a commonly observed phenomenon in HCRVs, and studying its impact on roll behaviour is important. In this study, the impact of the symmetric toe and thrust misalignment on the roll behaviour of an HCRV is analysed using IPG TruckMaker®, a vehicle dynamics simulation software. A ramp steer manoeuvre was used for the simulations, and the toe misalignment on a wheel was chosen from the range [-0.21°, 0.21°]. Variation in roll behaviour was quantified using the steering wheel angle at which one-wheel lift-off (OWL) occurred (SWAL).

The functional safety of electric vehicles has attracted a great deal of attention among automobile industries globally. A tricky yet necessary dual gamut of operational ease along with operational safety is something that cannot be ignored while using electric vehicles. Safety paired with vehicle reliability will go a long way in the market. Therefore, abnormal vehicle behavior due to factors such as unintended acceleration should not be kept in hindsight. Unintended acceleration is a phenomenon where the vehicle accelerates involuntarily without the knowledge of the driver which leads to accidents and fatal injuries. Thus, prior detection of unintended acceleration becomes mandatory for driver’s safety. Unintended acceleration is a result of various uncontrolled conditions like road driving conditions and system malfunction.

As we all know, automotive headliners are an essential component of any car’s interior as they cover all the internal components and provide a clean and finished look. Headliners not only increase the aesthetic appeal of a car’s interior, but also acts as an insulation and sound absorption source. As per the latest Government norms, Curtain Airbag (henceforth called as CAB) has been made mandatory and this change calls for the corresponding changes in the Headliner packaging of all passenger vehicles. In general, curtain air-bag deployment calls for a twist open of Headliner at lateral sides (a portion below Hinge-line) during the deployment. This enables the inflated airbag to flow inside the passenger cabin to protect the passenger from any injury. Conventionally no components are packaged below the hinge-line area of headliner to avoid obstruction for CAB deployment and any part fly-off concerns.